Panel Upgrades and Replacements in Sahuarita, AZ
Every circuit in a house runs through one gray metal box, usually on an outside wall or in the garage. When that panel is too small for the home's load, worn out, or one of the models known to fail, every other part of the electrical system inherits the problem. PNLS Electric LLC upgrades and replaces electrical panels for homeowners in Sahuarita who need more capacity or a panel they can trust.
Upgrade Versus Replacement
The two terms get used interchangeably, but they describe different jobs.
A replacement swaps an existing panel for a new one of the same capacity. The service coming into the house stays the same size. This makes sense when the panel is damaged, corroded, out of breaker spaces, or a model with a poor safety record, but the home's total load is fine.
An upgrade increases the amperage the house can draw, most often from 100 amps to 200. That usually means a new panel plus changes to the service entrance and meter base, and it involves the utility. Upgrades are for homes where the load has outgrown the service: more air conditioning, an electric vehicle, a pool, a workshop.

Signs a Panel Is Due
Breakers that trip during ordinary use, such as running the microwave and the toaster at once, can mean the circuits are overloaded or the breakers themselves are wearing out. Lights that dim every time the air conditioner cycles on may point to a service running near its limit.
Physical signs matter too. Rust inside the panel, scorch marks around a breaker, a breaker that feels hot, or a buzzing sound from the box all call for a closer look. So does a panel with every slot filled and double-tapped breakers carrying two wires where one belongs. And if the house still has screw-in fuses, it is overdue.
Panels Worth Replacing Regardless of Condition
Certain panels have a long record of breakers that may not trip when they should. Federal Pacific Electric panels with Stab-Lok breakers and Zinsco panels are the two most common in older homes. A breaker that fails to trip during an overload lets the wire behind it overheat. These panels can look fine from the outside for decades, which is part of what makes them a concern. If the label on yours carries one of those names, replacement is the safer course.
How the Work Usually Goes
It starts with a load calculation, which adds up what the home's appliances and systems draw and determines whether a replacement at the same size will do or an upgrade is needed.
On the day of the work, power to the house is shut off. For an upgrade, the utility disconnects service at the meter. The old panel comes out, the new one goes in, and each circuit is moved over, checked, and labeled. Wiring that does not meet current requirements gets corrected along the way. An inspection typically follows before full service is restored.
Planning for What Comes Next
A panel upgrade is a good time to think a few years ahead. If an electric vehicle is on the horizon, the new panel can be sized and laid out with an EV charger circuit in mind. If a kitchen or bathroom remodel is planned, the extra circuits it will need can be accounted for now rather than squeezed in later. PNLS Electric also handles the wiring side of small remodels. Other loads to consider: a pool pump, ductless mini-splits for a garage or casita, an induction range, or a heat pump water heater. Each one adds to the total, and a panel sized only for today will run short sooner.
Panel Work Around Sahuarita
Most panel jobs are right here in Sahuarita. Homeowners in Tucson, Nogales, and Marana can also get in touch about their panel. A summary of every service the company offers is on the PNLS Electric main page.
Panel Upgrade Questions
How do I find out what size service my house has?
Look at the main breaker, usually the large one at the top of the panel. The number stamped on its handle, such as 100, 150, or 200, is the service size in amps. If there is no main breaker, the panel label or the meter base may list the rating.
How long will the power be off?
A same-size replacement typically keeps the house without power for 4 to 8 hours. An upgrade that changes the service entrance can take longer, because it depends on when the utility disconnects and reconnects the meter. Refrigerators and freezers generally hold temperature for that window if their doors stay closed.
Is 200 amps enough for my house?
For most single-family homes, yes, including one with central air and a 40- or 48-amp EV charger. Homes that are fully electric, with two EVs, a pool, and electric heat, may need a load-management device or a larger service of 320 or 400 amps. The load calculation settles it.
Can I add tandem breakers instead of replacing a full panel?
Sometimes. Tandem breakers fit two circuits into one slot, but only in panels listed for them, and only in the specific slots the panel label allows. Installing them where they are not permitted creates an overloaded bus. If the label does not allow tandems, or those slots are already used, a larger panel is the answer.
What happens to my electric meter during an upgrade?
The meter belongs to the utility. During a service upgrade, the meter base it plugs into is often replaced to handle the higher amperage. The utility pulls the meter at the start and sets it again once the new equipment passes inspection.




